科创中国

近年来178Hfm2 31年的同核异能态被认为是用低能X射线触发使其释放储存能量的最合适候选者.为了探讨在178Hf中是否存在触发Kπ=16+同核异能态γ发射的门态,本工作首先用投影壳模型对178Hf的多准粒子态和集体激发态进行了研究,结果表明其它态位于距离16+同核异能态较远的地方.但当用包括γ自由度的组态限制(绝热阻塞)方法计算178Hf的多准粒子激发态时,结果显示有三个能级可能是16+同核异能态光退激的候选者,位能面计算的结果显示178Hf为轴对称硬核.

In precision machining of complex curved surface parts with high performance, geometry accuracy is not the only constraint, but the performance should also be met. Performance of this kind of parts is closely related to the geometrical and physical parameters, so the final actual size and shape are affected by multiple source constraints, such as geometry, physics, and performance. These parts are rather difficult to be manufactured and new manufacturing method according to performance requirement is urgently needed. Based on performance and manufacturing requirements for complex curved surface parts, a new classification method is proposed, which divided the complex curved surface parts into two categories: surface re-design complex curved surface parts with multi-source constraints(PRCS) and surface unique complex curved surface parts with pure geometric constraints(PUCS). A correlation model is constructed between the performance and multi-source constraints for PRCS, which reveals the correlation between the performance and multi-source constraints. A re-design method is also developed. Through solving the correlation model of the typical part's performance-associated surface, the mapping relation between the performance-associated surface and the related removal amount is obtained. The explicit correlation model and the method for the corresponding related removal amount of the performance-associated surface are built based on the classification of surface re-design complex curved surface parts with multi-source constraints. Research results have been used in the actual processing of the typical parts such as radome, common bottom components, nozzle, et al., which shows improved efficiency and accuracy of the precision machining for the surface re-design parts with complex curved surface.

As the two most important indexes of bearing raceway,surface roughness and roundness have significant influence on bearing noise.Some researchers have carried out studies in this field,however,reason and extent of the influence of raceway surface geometric characteristics on bearing running noise are not perfectly clear up to now.In this paper,the raceway of 6309 type bearing's inner and outer ring is machined by floating abrasive polishing adopting soft abrasive pad.Surface roughness parameters,arithmetical mean deviation of the profile Ra,the point height of irregularities Rz,maximum height of the profile Rmax and roundness f of raceways,are measured before and after machining,and the change rules of the measured results are studied.The study results show that the floating abrasive polishing can reduce the surface geometric errors of bearing raceway evidently.The roundness error is reduced by 25%,Rmax value is reduced by 35.5%,Rz value is reduced by 22%and Ra value is reduced by 5%.By analyzing the change of the geometrical parameters and the shape difference of the raceway before and after machining,it is found that the floating abrasive polishing method can affect the roundness error mainly by modifying the local deviation of the raceway's surface profile.Bearings with different raceway surface geometrical parameter value are assembled and the running noise is tested.The test results show that Ra has a little,Rmax and Rz have a measurable,and the roundness error has a significant influence on the running noise.From the viewpoint of controlling bearings'running noise,raceway roundness error should be strictly controlled,and for the surface roughness parameters,Rmax and Rz should be mainly controlled.This paper proposes an effective method to obtain the low noise bearing by machining the raceway with floating abrasive polishing after super finishing.

"十二五"时期我国节能工作面临着更加复杂的形势和严峻的挑战,需要在以往工作基础上有所创新和突破.日本是全球能源效率最高的国家之一,节能取得卓越成绩不仅依靠对技术的不懈追求,更依靠对节能更加深入的理解和政策上的大胆尝试.通过将节能融入经济发展战略、"以人为本"的管理手段以及用更加系统整体的眼光重新看待节能技术和产品,加上能源管理师、领跑者等制度上的创新,日本一直保持着全球节能引领者地位.本文简要地回顾和总结了日本近年来节能理念和制度方面的创新,并结合我国"十一五"以来节能工作,提出了针对"十二五"节能工作的政策建议.

Quadruped robots consume a lot of energy,which is one of the factors restricting their application.Energy efficiency is one of the key evaluating indicators for walking robots.The relationship between energy and elastic elements of walking robots have been studied,but different walking gait patterns and contact status have important influences on locomotion energy efficiency,and the energy efficiency considering the foot-end trajectory has not been reported.Therefore,the energy consumption and energy efficiency of quadruped robot with trot gait and combined cycloid foot trajectory are studied.The forward and inverse kinematics of quadruped robot is derived.The combined cycloid function is proposed to generate horizontal and vertical foot trajectory respectively,which can ensure the acceleration curve of the foot-end smoother and more successive,and reduce the contact force between feet and environment.Because of the variable topology mechanism characteristic of quadruped robot,the leg state is divided into three different phases which are swing phase,transition phase and stance phase during one trot gait cycle.The non-continuous variable constraint between feet and environment of quadruped robot is studied.The dynamic model of quadruped robot is derived considering the variable topology mechanism characteristic,the periodic contact and elastic elements of the robot.The total energy consumption of walking robot during one gait cycle is analyzed based on the dynamic model.The specific resistance is used to evaluate energy efficiency of quadruped robot.The calculation results show the relationships between specific resistance and gait parameters,which can be used to determine the reasonable gait parameters.

新国标(GBl8613)将在2012年内发布并正式开始实施,对新旧标准分别进行了介绍,具体分析了新国标颁布实施后,可能会给中小型电机行业带来的影响,企业应做好相应的技术准备.

During hard cutting process there is severe thermodynamic coupling effect between cutting tool and workpiece, which causes quenching effect on finished surfaces under certain conditions. However, material phase transformation mechanism of heat treatment in cutting process is different from the one in traditional process, which leads to changes of the formation mechanism of damaged layer on machined workpiece surface. This paper researches on the generation mechanism of damaged layer on machined surface in the process of PCBN tool hard cutting hardened steel Cr12 Mo V. Rules of temperature change on machined surface and subsurface are got by means of finite element simulation. In phase transformation temperature experiments rapid transformation instrument is employed, and the effect of quenching under cutting conditions on generation of damaged layer is revealed. Based on that, the phase transformation points of temperature under cutting conditions are determined. By experiment, the effects of cutting speed and tool wear on white layer thickness in damaged layer are revealed. The temperature distribution law of third deformation zone is got by establishing the numerical prediction model, and thickness of white layer in damaged layer is predicted, taking the tool wear effect into consideration. The experimental results show that the model prediction is accurate, and the establishment of prediction model provides a reference for wise selection of parameters in precise hard cutting process. For the machining process with high demanding on surface integrity, the generation of damaged layer on machined surface can be controlled precisely by using the prediction model.

With the increasing noise pollution,low noise optimization of centrifugal pimps has become a hot topic.However,experimental study on this problem is unacceptable for industrial applications due to unsustainable cost.A hybrid method that couples computational fluid dynamics(CFD)with computational aeroacoustic software is used to predict the flow-induced noise of pumps in order to minimize the noise of centrifugal pumps in actual projects.Under Langthjem's assumption that the blade surface pressure is the main flow-induced acoustic source in centrifugal pumps,the blade surface pressure pulsation is considered in terms of the acoustical sources and simulated using CFX software.The pressure pulsation and noise distribution in the near-cutoff region are examined for the blade-passing frequency(BPF)noise,and the sound pressure level(SPL)reached peaks near the cutoff that corresponded with the pressure pulsation in this region.An experiment is performed to validate this prediction.Four hydrophones are fixed to the inlet and outlet ports of the test pump to measure the flow-induced noise from the four-port model.The simulation results for the noise are analyzed and compared with the experimental results.The variation in the calculated noise with changes in the flow agreed well with the experimental results.When the flow rate was increased,the SPL first decreased and reached the minimum near the best efficient point(BEP);it then increased when the flow rate was further increased.The numerical and experimental results confirmed that the BPF noise generated by a blade-rotating dipole roughly reflects the acoustic features of centrifugal pumps.The noise simulation method in current study has a good feasibility and suitability,which could be adopted in engineering design to predict and optimize the hydroacoustic behavior of centrifugal pumps.

Objective To detect the cell viability and the expressions of stem cell surface markers after chemotherapeutic drug treatment.Methods We observed the cytotoxic effects of three chemotherapeutic agents[epirubicin(Epi),fluorouracil(5-FU)and cyclophosphamide(Cyc)]in three cell lines,and the cell viabilities after removed these chemotherapeutic agents.Expressions of stem cell surface markers CD44,CD24,CD90,CD14 and aldehyde dehydrogenase1(ALDH1)in breast cancer cells were analyzed by real-time PCR.The post hoc analysis(Tukey's tests)in conjunction with one-way ANOVA was used for statistical analysis.Results The initial cytotoxic efficacy was most notable.After the treatment of the same therapeutic agents,cell viability was decreased by 64.8%35.14%,32.25%in BT-483 cells,66.4%,22.94%and 45.88%in MDA-MB-231 cells,97.1%,99.5%and 76.4%in MCF cells.The difference was significant compared with that before treatment(P=0.000).However,the inhibitory effects were diminished after chemotherapeutic agent withdrawal.Cell viabilities were increased to 167.9%,212.04%and 188.66%in MDA-MB-231 cells at48 h after withdrawal.At 72 h after withdrawal,cell viability was increased with a significant difference in three cell lines(all P values=0.000).Expressions of CD44 and ALDH1 were most prevalent for MDA-MB-231,BT-483 and MCF-7 cells.ALDH1 mRNA level was significant higher in BT-483(HER-2 overexpression cell line)than MDA-MB-231(triple negative cell line)(P=0.012).CD14 mRNA level in MCF-7 cells were significantly lower than that in MDA-MB-231 and BT-483(P=0.003,0.001).BT-483 showed significantly higher level of CD44 than MDA-MB-231 and MCF-7 cell line(P=0.013,0.020),and no significant difference was detected between MDA-MB-231 and MCF-7 breast cancer cells(P=0.955).CD90 mRNA expressions were detected in MDA-MB-231 cells and MCF-7 cells,but not in BT-483 cells.Conclusion Some malignant cells could survive in vitro and begin to proliferate again between cycles of chemotherapy.

The existing research of the acceleration control mainly focuses on an optimization of the velocity trajectory with respect to a criterion formulation that weights acceleration time and fuel consumption. The minimum-fuel acceleration problem in conventional vehicle has been solved by Pontryagin's maximum principle and dynamic programming algorithm, respectively. The acceleration control with minimum energy consumption for battery electric vehicle(EV) has not been reported. In this paper, the permanent magnet synchronous motor(PMSM) is controlled by the field oriented control(FOC) method and the electric drive system for the EV(including the PMSM, the inverter and the battery) is modeled to favor over a detailed consumption map. The analytical algorithm is proposed to analyze the optimal acceleration control and the optimal torque versus speed curve in the acceleration process is obtained. Considering the acceleration time, a penalty function is introduced to realize a fast vehicle speed tracking. The optimal acceleration control is also addressed with dynamic programming(DP). This method can solve the optimal acceleration problem with precise time constraint, but it consumes a large amount of computation time. The EV used in simulation and experiment is a four-wheel hub motor drive electric vehicle. The simulation and experimental results show that the required battery energy has little difference between the acceleration control solved by analytical algorithm and that solved by DP, and is greatly reduced comparing with the constant pedal opening acceleration. The proposed analytical and DP algorithms can minimize the energy consumption in EV's acceleration process and the analytical algorithm is easy to be implemented in real-time control.