科创中国

对外径为Ф10mm碳纤维复合材料管成型工艺及性能进行了研究.结果表明,采用热缩工艺成型的碳纤维复合材料管工艺简单、质量可靠,Ф10mm碳纤维复合材料管件弯曲刚度与不锈钢管相当,弯曲强度为不锈钢的3倍以上,质量仅为不锈钢的50%,尺寸精度满足设计要求.

Iterative methods based on finite element simulation are effective approaches to design mold shape to compensate springback in sheet metal forming.However,convergence rate of iterative methods is difficult to improve greatly.To increase the springback compensate speed of designing age forming mold,process of calculating springback for a certain mold with finite element method is analyzed.Springback compensation is abstracted as finding a solution for a set of nonlinear functions and a springback compensation algorithm is presented on the basis of quasi Newton method.The accuracy of algorithm is verified by developing an ABAQUS secondary development program with MATLAB.Three rectangular integrated panels of dimensions 710 mm′750 mm integrated panels with intersected ribs of 10 mm are selected to perform case studies.The algorithm is used to compute mold contours for the panels with cylinder,sphere and saddle contours respectively and it takes 57%,22%and 33%iterations as compared to that of displacement adjustment(DA)method.At the end of iterations,maximum deviations on the three panels are 0.618 4 mm,0.624 1 mm and 0.342 0 mm that are smaller than the deviations determined by DA method(0.740 8 mm,0.740 8 mm and 0.713 7 mm respectively).In following experimental verification,mold contour for another integrated panel with 400 mm*380 mm size is designed by the algorithm.Then the panel is age formed in an autoclave and measured by a three dimensional digital measurement devise.Deviation between measuring results and the panel's design contour is less than 1 mm.Finally,the iterations with different mesh sizes(40 mm,35mm,30 mm,25 mm,20 mm)in finite element models are compared and found no considerable difference.Another possible compensation method,Broyden-Fletcher-Shanmo method,is also presented based on the solving nonlinear functions idea.The Broyden-Fletcher-Shanmo method is employed to compute mold contour for the second panel.It only takes 50%iterations compared to that of DA.The proposed method can serve a faster mold contour compensation method for sheet metal forming.

探究了Vectran长丝纱在剑杆小样机上试织平纹织物的主要工艺设计和上机织造情况.研究Vectran长丝纱的可织性,探索利用Vectran长丝纱开发新型产业用纺织品的途径.结果表明其可织性与芳纶类似,主要问题是其织造张力难以均匀控制,且易钩丝,应对长丝纱作前处理并合理控制织造工艺.

Forming limit curves(FLCs) are commonly used for evaluating the formability of sheet metals. However, it is difficult to obtain the FLCs with desirable accuracy by experiments due to that the friction effects are non-negligible under warm/hot stamping conditions. To investigate the experimental errors, experiments for obtaining the FLCs of the AA5754 are conducted at 250℃. Then, FE models are created and validated on the basis of experimental results. A number of FE simulations are carried out for FLC test-pieces and punches with different geometry configurations and varying friction coefficients between the test-piece and the punch. The errors for all the test conditions are predicted and analyzed. Particular attention of error analysis is paid to two special cases, namely, the biaxial FLC test and the uniaxial FLC test. The failure location and the variation of the error with respect to the friction coefficient are studied as well. The results obtained from the FLC tests and the above analyses show that, for the biaxial tension state, the friction coefficient should be controlled within 0.15 to avoid significant shifting of the necking location away from the center of the punch; for the uniaxial tension state, the friction coefficient should be controlled within 0.1 to guarantee the validity of the data collected from FLC tests. The conclusions summarized are beneficial for obtaining accurate FLCs under warm/hot stamping conditions.

Bearing ring is the crucial component of bearing. With regard to such problems as material waste, low efficiency and high energy consumption in current process of producing large bearing ring, a new process named "casting-rolling compound forming technology" is researched by taking the typical 42CrMo slew bearing as object. Through theoretical analysis, the design criteria of the main casting-rolling forming parameters are put forward at first. Then the constitutive relationship model of as-cast 42CrMo steel and its mathematical model of dynamic recrystallization are obtained according to the results of the hot compression experiment. By a coupled thermal-mechanical finite element model for radial-axial rolling of bearing ring, the fraction of dynamic recrystallization is calculated and recrystallized grains size are predicated. Meanwhile, the effects of the initial rolling temperature and feed rate of idle roll on material microstructure evolution are analyzed. Finally, the industrial rolling experiment is designed and performed, based on the simulation results. In addition, mechanical and metallographic tests are conducted on rolled bearing ring to get the mechanical parameters and metallographic structure. The experimental data and results show that the mechanical properties of bearing ring produced by casting-rolling compound forming technology are up to industrial standard, and a qualified bearing ring can be successfully formed by employing this new technology. Through the study, a process of forming large bearing ring directly by using casting ring blank is obtained, which could provide an effective theoretical guidance for manufacturing large ring parts. It also has an edge in saving material, lowering energy and improving efficiency.

The existing research of process capability indices of multiple quality characteristics mainly focuses on nonconforming of process output, the concept development of univariate process capability indices, quality loss function and various comprehensive evaluation methods. The multivariate complexity increases the computation difficulty of multivariate process capability indices(MPCI), which makes them hard to be used in practice. In this paper, a new PCA-based MPCI approach is proposed to assess the production capability of the processes that involve multiple product quality characteristics. This approach first transforms the original quality variables into standardized normal variables. MPCI measures are then provided based on the Taam index. Moreover, the statistical properties of these MPCIs, such as confidence intervals and lower confidence bound, are given to let the practitioners understand the capability indices as random variables instead of deterministic variables. A real manufacturing data set and a synthetic data set are used to demonstrate the effectiveness of the proposed method. An implementation procedure is also provided for quality engineers to apply our MPCI approach in their manufacturing processes. The case studies demonstrate the effectiveness and feasibility of this new kind of MPCI, which is easier to be used in production practice. The proposed research provides a novel approach of MPCI calculation.

采用PFA材料所成型的油封在机床油管中起到密封和显示油液位置的作用,以解决机床油路部分漏油的问题.为确保油封质量合格,运用CAE软件Moldflow模拟了油封塑料熔体在模具模腔中的流动、保压、冷却过程,预测制品可能发生的翘曲、气穴、熔接痕等缺陷,据此对油封模具的结构和注塑工艺参数优化,并介绍外骨架油封批量生产的模具设计及工作过程,提高了一次试模的成功率,加快了模具开发进度,进而缩短产品开发周期,提高企业的配套能力和产品质量.

主要介绍了徐州香山物流流程设计优化问题,并具体对该企业仓储、运输现状进行分析,提出了具体的优化措施和方案.

在综合比较知识管理成熟度模型的基础上,充分借鉴诸多知识管理成熟度模型的特性,结合我国企业知识管理实践,提出企业知识管理成熟度整合模型,并深入剖析其逻辑结构、成熟等级、关键过程领域以及实施程序,为现代企业有效实施知识管理项目,提升知识管理能力和绩效提供借鉴和帮助.

根据现代物流的发展,提出物流的物品、过程两个基本假设,沿着这两条主线,结合物流系统结构、实体物流表现、物流学科设置,理论联系实际分析了物流系统框架.