科创中国

科研中经常遇到涉及两个因素的实验,若两因素有交互作用,则需采用析因设计、正交设计等设计类型,但这些设计通常需要进行较多次实验.若在理论和专业上可以证明,实验中涉及到的两个因素不存在交互作用,或交互作用对观测结果的影响无统计学意义,并且特定实验条件(通常为各因素不同水平的一种组合)下实验数据的测定误差在专业上允许的范围之内,则可采用无重复实验的随机区组设计、无重复实验的平衡不完全随机区组设计、具有一个重复测量的单因素设计、无重复实验双因素设计和两因素嵌套设计.本文结合实例,重点介绍后两种实验设计类型.

It is a common phenomenon that the cracks originating from a hole can cause structural damage in engineering.However,the fracture mechanics studies of hole edge crack problems are not sufficient.The problem of an elliptical hole with two collinear edge cracks of unequal length in an infinite plate under uniform tension at infinity is investigated.Based on the complex variable method,the analytical solutions of stress functions and stress intensity factors are provided.The stress distribution along the axes and the edge of the elliptical hole is given graphically.The numerical results show that there is obvious stress concentration near the hole and cracks,and the stresses tend to applied loads at distances far from the defect,which conform to Saint-Venant's principle.Hence,the stress functions are proved to be right.Under special conditions,the present configuration becomes the Griffith crack,two symmetrical cracks emanating from an elliptical hole,two cracks of unequal length emanating from a circular hole,a crack at the edge of a circular hole,or a crack emanating from an elliptical hole.Compared with available results,stress intensity factors for these special shapes of ellipses and cracks show good coincidence.The stress intensity factor for two cracks of unequal length at the edge of an elliptical hole increases with the crack length and the major-to-minor axis ratio of the elliptical hole.The stress distribution in an infinite plate containing an elliptic hole with unsymmetrical cracks is given for the first time.

Forming limit curves(FLCs) are commonly used for evaluating the formability of sheet metals. However, it is difficult to obtain the FLCs with desirable accuracy by experiments due to that the friction effects are non-negligible under warm/hot stamping conditions. To investigate the experimental errors, experiments for obtaining the FLCs of the AA5754 are conducted at 250℃. Then, FE models are created and validated on the basis of experimental results. A number of FE simulations are carried out for FLC test-pieces and punches with different geometry configurations and varying friction coefficients between the test-piece and the punch. The errors for all the test conditions are predicted and analyzed. Particular attention of error analysis is paid to two special cases, namely, the biaxial FLC test and the uniaxial FLC test. The failure location and the variation of the error with respect to the friction coefficient are studied as well. The results obtained from the FLC tests and the above analyses show that, for the biaxial tension state, the friction coefficient should be controlled within 0.15 to avoid significant shifting of the necking location away from the center of the punch; for the uniaxial tension state, the friction coefficient should be controlled within 0.1 to guarantee the validity of the data collected from FLC tests. The conclusions summarized are beneficial for obtaining accurate FLCs under warm/hot stamping conditions.

通过对三相异步电机功率因数控制器的工作原理分析,找出双向晶闸管的输出电压与其可控角之间的关系,提出了将功率因数控制器对晶闸管控制角控制计算转换为对时间控制的新控制算法.分析触发时间与输出电压之间的关系及触发方法,电机负载、功率因数与节能之间的关系,提出了功率因数控制器控制算法的两种控制方案,给出了控制算法程序框图,使单片机的软件设计实施方案更加方便.

The idle time which is part of the order fulfillment time is decided by the number of items in the zone; therefore the item assignment method affects the picking efficiency. Whereas previous studies only focus on the balance of number of kinds of items between different zones but not the number of items and the idle time in each zone. In this paper, an idle factor is proposed to measure the idle time exactly. The idle factor is proven to obey the same vary trend with the idle time, so the object of this problem can be simplified from minimizing idle time to minimizing idle factor. Based on this, the model of item assignment problem in synchronized zone automated order picking system is built. The model is a form of relaxation of parallel machine scheduling problem which had been proven to be NP-complete. To solve the model, a taboo search algorithm is proposed. The main idea of the algorithm is minimizing the greatest idle factor of zones with the 2-exchange algorithm. Finally, the simulation which applies the data collected from a tobacco distribution center is conducted to evaluate the performance of the algorithm. The result verifies the model and shows the algorithm can do a steady work to reduce idle time and the idle time can be reduced by 45.63% on average. This research proposed an approach to measure the idle time in synchronized zone automated order picking system. The approach can improve the picking efficiency significantly and can be seen as theoretical basis when optimizing the synchronized automated order picking systems.

目的表皮干细胞是组织工程化皮肤的"种子细胞".文中研究碱性成纤维细胞生长因子(basic fibroblast growth factor,bFGF)、胰岛素样细胞生长因子-1(insulin-like growth factor-1,IGF-1)和转化生长因子仅(transforming growth factor a,TGFa)对人表皮干细胞增殖的影响.方法采用两步酶消化法和Ⅳ型胶原差速贴壁相结合的方法获得人原代表皮干细胞,将表皮干细胞分为A组(K-SFM)、B组(K-SFM+bFGF)、C组(K-SFM+IGF-1)及D组(K-SFM+TGFot)进行培养.比较不同组之间表皮干细胞的克隆形成率、生长增殖、生长曲线和细胞周期等指标.结果B组、C组及D组培养的表皮干细胞在细胞增殖、细胞克隆率方面检测结果均明显高于A组(P〈0.05);流式细胞仪检测B组、C组与A组及D组处于G0/G1细胞比例比较差异有统计学意义(P〈0.05).结论IGF-1、bFGF及TGF-a均对表皮干细胞的增殖有促进作用,IGF-1及bFGF对表皮干细胞表型的维持有较好的作用.

Existing biped robots mainly fall into two categories: robots with left and right feet and robots with upper and lower feet. The load carrying capability of a biped robot is quite limited since the two feet of a walking robot supports the robot alternatively during walking. To improve the load carrying capability, a novel biped walking robot is proposed based on a 2-UPU+2-UU parallel mechanism. The biped walking robot is composed of two identical platforms(feet) and four limbs, including two UPU(universal-prismatic-universal serial chain) limbs and two UU limbs. To enhance its terrain adaptability like articulated vehicles, the two feet of the biped walking robot are designed as two vehicles in detail. The conditions that the geometric parameters of the feet must satisfy are discussed. The degrees-of-freedom of the mechanism is analyzed by using screw theory. Gait analysis, kinematic analysis and stability analysis of the mechanism are carried out to verify the structural design parameters. The simulation results validate the feasibility of walking on rugged terrain. Experiments with a physical prototype show that the novel biped walking robot can walk stably on smooth terrain. Due to its unique feet design and high stiffness, the biped walking robot may adapt to rugged terrain and is suitable for load-carrying.

The classical natural coordinate modeling method which removes the Euler angles and Euler parameters from the governing equations is particularly suitable for the sensitivity analysis and optimization of multibody systems. However, the formulation has so many principles in choosing the generalized coordinates that it hinders the implementation of modeling automation. A first order direct sensitivity analysis approach to multibody systems formulated with novel natural coordinates is presented. Firstly, a new selection method for natural coordinate is developed. The method introduces 12 coordinates to describe the position and orientation of a spatial object. On the basis of the proposed natural coordinates, rigid constraint conditions, the basic constraint elements as well as the initial conditions for the governing equations are derived. Considering the characteristics of the governing equations, the newly proposed generalized-α integration method is used and the corresponding algorithm flowchart is discussed. The objective function, the detailed analysis process of first order direct sensitivity analysis and related solving strategy are provided based on the previous modeling system. Finally, in order to verify the validity and accuracy of the method presented, the sensitivity analysis of a planar spinner-slider mechanism and a spatial crank-slider mechanism are conducted. The test results agree well with that of the finite difference method, and the maximum absolute deviation of the results is less than 3%. The proposed approach is not only convenient for automatic modeling, but also helpful for the reduction of the complexity of sensitivity analysis, which provides a practical and effective way to obtain sensitivity for the optimization problems of multibody systems.

As one of the most wear monitoring indicator, dimensional feature of individual particles has been studied mostly focusing on off-line analytical ferrograph. Recent development in on-line wear monitoring with wear debris images shows that merely wear debris concentration has been extracted from on-line ferrograph images. It remains a bottleneck of obtaining the dimension of on-line particles due to the low resolution, high contamination and particle's chain pattern of an on-line image sample. In this work, statistical dimension of wear debris in on-line ferrograph images is investigated. A two-step procedure is proposed as follows. First, an on-line ferrograph image is decomposed into four component images with different frequencies. By doing this, the size of each component image is reduced by one fourth, which will increase the efficiency of subsequent processing. The low-frequency image is used for extracting the area of wear debris, and the high-frequency image is adopted for extracting contour. Second, a statistical equivalent circle dimension is constructed by equaling the overall wear debris in the image into equivalent circles referring to the extracted total area and premeter of overall wear debris. The equivalent circle dimension, reflecting the statistical dimension of larger wear debris in an on-line image, is verified by manual measurement. Consequently, two preliminary applications are carried out in gasoline engine bench tests of durability and running-in. Evidently, the equivalent circle dimension, together with the previously developed concentration index, index of particle coverage area(IPCA), show good performances in characterizing engine wear conditions. The proposed dimensional indicator provides a new statistical feature of on-line wear particles for on-line wear monitoring. The new dimensional feature conveys profound information about wear severity.

The current development of precision plastic injection molding machines mainly focuses on how to save material and improve precision, but the two aims contradict each other. For a clamp unit, clamping precision improving depends on the design quality of the stationary platen. Compared with the parametric design of stationary platen, structural scheme design could obtain the optimization model with double objectives and multi-constraints. In this paper, a SE-160 precision plastic injection molding machine with 1600 kN clamping force is selected as the subject in the case study. During the motion of mold closing and opening, the stationary platen of SE-160 is subjected to a cyclic loading, which would cause the fatigue rupture of the tie bars in periodically long term operations. In order to reduce the deflection of the stationary platen, the FEA method is introduced to optimize the structure of the stationary platen. Firstly, an optimal topology model is established by variable density method. Then, structural topology optimizations of the stationary platen are done with the removable material from 50%, 60% to 70%. Secondly, the other two recommended optimization schemes are given and compared with the original structure. The result of performances comparison shows that the scheme II of the platen is the best one. By choosing the best alternative, the volume and the local maximal stress of the platen could be decreased, corresponding to cost-saving material and better mechanical properties. This paper proposes a structural optimization design scheme, which can save the material as well as improve the clamping precision of the precision plastic injection molding machine.