科创中国

It is significant to develop a robot hand with high rigidity by a 6-DOF parallel manipulator(PM).However,the existing6-DOF PMs include spherical joint which has less capability of pulling force bearing,less rotation range and lower precision under alternately heavy loads.A novel 6-DOF PM with three planar limbs and equipped with three fingers is proposed and its kinematics and statics are analyzed systematically.A 3-dimension simulation mechanism of the proposed manipulator is constructed and its structure characteristics is analyzed.The kinematics formulae for solving the displacement,velocity,acceleration of the platform,the active legs and the fingers are established.The statics formulae are derived for solving the active forces of PM and the finger mechanisms.An analytic example is given for solving the kinematics and statics of proposed manipulator and the analytic solved results are verified by the simulation mechanism.It is proved from the error analysis of analytic solutions and simulation solutions that the derived analytic formulae are correct and provide the theoretical and technical foundations for its manufacturing,control and application.

Existing biped robots mainly fall into two categories: robots with left and right feet and robots with upper and lower feet. The load carrying capability of a biped robot is quite limited since the two feet of a walking robot supports the robot alternatively during walking. To improve the load carrying capability, a novel biped walking robot is proposed based on a 2-UPU+2-UU parallel mechanism. The biped walking robot is composed of two identical platforms(feet) and four limbs, including two UPU(universal-prismatic-universal serial chain) limbs and two UU limbs. To enhance its terrain adaptability like articulated vehicles, the two feet of the biped walking robot are designed as two vehicles in detail. The conditions that the geometric parameters of the feet must satisfy are discussed. The degrees-of-freedom of the mechanism is analyzed by using screw theory. Gait analysis, kinematic analysis and stability analysis of the mechanism are carried out to verify the structural design parameters. The simulation results validate the feasibility of walking on rugged terrain. Experiments with a physical prototype show that the novel biped walking robot can walk stably on smooth terrain. Due to its unique feet design and high stiffness, the biped walking robot may adapt to rugged terrain and is suitable for load-carrying.

The compliance modeling and rigidity performance evaluation for the lower mobility parallel manipulators are still to be remained as two overwhelming challenges in the stage of conceptual design due to their geometric complexities. By using the screw theory, this paper explores the compliance modeling and eigencompliance evaluation of a newly patented 1T2R spindle head whose topological architecture is a 3-RPS parallel mechanism. The kinematic definitions and inverse position analysis are briefly addressed in the first place to provide necessary information for compliance modeling. By considering the 3-RPS parallel kinematic machine(PKM) as a typical compliant parallel device, whose three limb assemblages have bending, extending and torsional deflections, an analytical compliance model for the spindle head is established with screw theory and the analytical stiffness matrix of the platform is formulated. Based on the eigenscrew decomposition, the eigencompliance and corresponding eigenscrews are analyzed and the platform's compliance properties are physically interpreted as the suspension of six screw springs. The distributions of stiffness constants of the six screw springs throughout the workspace are predicted in a quick manner with a piece-by-piece calculation algorithm. The numerical simulation reveals a strong dependency of platform's compliance on its configuration in that they are axially symmetric due to structural features. At the last stage, the effects of some design variables such as structural, configurational and dimensional parameters on system rigidity characteristics are investigated with the purpose of providing useful information for the structural design and performance improvement of the PKM. Compared with previous efforts in compliance analysis of PKMs, the present methodology is more intuitive and universal thus can be easily applied to evaluate the overall rigidity performance of other PKMs with high efficiency.

Parallel kinematic machines have drawn considerable attention and have been widely used in some special fields.However,high precision is still one of the challenges when they are used for advanced machine tools.One of the main reasons is that the kinematic chains of parallel kinematic machines are composed of elongated links that can easily suffer deformations,especially at high speeds and under heavy loads.A 3-RRR parallel kinematic machine is taken as a study object for investigating its accuracy with the consideration of the deformations of its links during the motion process.Based on the dynamic model constructed by the Newton-Euler method,all the inertia loads and constraint forces of the links are computed and their deformations are derived.Then the kinematic errors of the machine are derived with the consideration of the deformations of the links.Through further derivation,the accuracy of the machine is given in a simple explicit expression,which will be helpful to increase the calculating speed.The accuracy of this machine when following a selected circle path is simulated.The influences of magnitude of the maximum acceleration and external loads on the running accuracy of the machine are investigated.The results show that the external loads will deteriorate the accuracy of the machine tremendously when their direction coincides with the direction of the worst stiffness of the machine.The proposed method provides a solution for predicting the running accuracy of the parallel kinematic machines and can also be used in their design optimization as well as selection of suitable running parameters.

The methods of improving the dynamic performance of high speed on/off solenoid valve include increasing the magnetic force of armature and the slew rate of coil current, decreasing the mass and stroke of moving parts. The increase of magnetic force usually leads to the decrease of current slew rate, which could increase the delay time of the dynamic response of solenoid valve. Using a high voltage to drive coil can solve this contradiction, but a high driving voltage can also lead to more cost and a decrease of safety and reliability. In this paper, a new scheme of parallel coils is investigated, in which the single coil of solenoid is replaced by parallel coils with same ampere turns. Based on the mathematic model of high speed solenoid valve, the theoretical formula for the delay time of solenoid valve is deduced. Both the theoretical analysis and the dynamic simulation show that the effect of dividing a single coil into N parallel sub-coils is close to that of driving the single coil with N times of the original driving voltage as far as the delay time of solenoid valve is concerned. A specific test bench is designed to measure the dynamic performance of high speed on/off solenoid valve. The experimental results also prove that both the delay time and switching time of the solenoid valves can be decreased greatly by adopting the parallel coil scheme. This research presents a simple and practical method to improve the dynamic performance of high speed on/off solenoid valve.

The existing researches on singularity of parallel mechanism are mostly limited to the property and regularity of singularity locus and there is no further research into the geometric relationship between uncontrolled kinematic screw and parallel mechanism in singularity.A 3UPS-S parallel mechanism is presented which fulfils 3-DOF in rotation.The regularity of nutation angle singularity is analyzed based on the Jacobian matrix,and the singularity surface of 3UPS-S parallel mechanisms is obtained.By applying the concept of reciprocal product in screw theory,the singular kinematic screw is derived when 3UPS-S parallel mechanism is in singularity.The geometric relationship between singular kinematic screw and singular configuration of 3UPS-S parallel mechanism is investigated by using programs in MATLAB.It is revealed that there are two kinds of situation.Firstly,the three limbs of 3UPS-S parallel mechanism intersect the singular kinematic screw in space simultaneously;Secondly,two limbs cross the singular kinematic screw while the third limb parallels with that screw.It is concluded that the nutation angle singularity of 3UPS-S parallel mechanism belongs to the singular linear complexes.This paper sheds light into and clarifies the geometric relationship between singular kinematic screw and singular configuration of 3UPS-S parallel mechanism.

Most gait studies of multi-legged robots in past neglected the dexterity of robot body and the relationship between stride length and body height.This paper investigates the performance of a radial symmetrical hexapod robot based on the dexterity of parallel mechanism.Assuming the constraints between the supporting feet and the ground with hinges,the supporting legs and the hexapod body are taken as a parallel mechanism,and each swing leg is regarded as a serial manipulator.The hexapod robot can be considered as a series of hybrid serial-parallel mechanisms while walking on the ground.Locomotion performance can be got by analyzing these equivalent mechanisms.The kinematics of the whole robotic system is established,and the influence of foothold position on the workspace of robot body is analyzed.A new method to calculate the stride length of multi-legged robots is proposed by analyzing the relationship between the workspaces of two adjacent equivalent parallel mechanisms in one gait cycle.Referring to service region and service sphere,weight service sphere and weight service region are put forward to evaluate the dexterity of robot body.The dexterity of single point in workspace and the dexterity distribution in vertical and horizontal projection plane are demonstrated.Simulation shows when the foothold offset goes up to 174 mm,the dexterity of robot body achieves its maximum value 0.164 4 in mixed gait.The proposed methods based on parallel mechanisms can be used to calculate the stride length and the dexterity of multi-legged robot,and provide new approach to determine the stride length,body height,footholds in gait planning of multi-legged robot.

Parallel robots with SCARA(selective compliance assembly robot arm) motions are utilized widely in the field of high speed pick-and-place manipulation. Error modeling for these robots generally simplifies the parallelogram structures included by the robots as a link. As the established error model fails to reflect the error feature of the parallelogram structures, the effect of accuracy design and kinematic calibration based on the error model come to be undermined. An error modeling methodology is proposed to establish an error model of parallel robots with parallelogram structures. The error model can embody the geometric errors of all joints, including the joints of parallelogram structures. Thus it can contain more exhaustively the factors that reduce the accuracy of the robot. Based on the error model and some sensitivity indices defined in the sense of statistics, sensitivity analysis is carried out. Accordingly, some atlases are depicted to express each geometric error's influence on the moving platform's pose errors. From these atlases, the geometric errors that have greater impact on the accuracy of the moving platform are identified, and some sensitive areas where the pose errors of the moving platform are extremely sensitive to the geometric errors are also figured out. By taking into account the error factors which are generally neglected in all existing modeling methods, the proposed modeling method can thoroughly disclose the process of error transmission and enhance the efficacy of accuracy design and calibration.