科创中国

It is a common phenomenon that the cracks originating from a hole can cause structural damage in engineering.However,the fracture mechanics studies of hole edge crack problems are not sufficient.The problem of an elliptical hole with two collinear edge cracks of unequal length in an infinite plate under uniform tension at infinity is investigated.Based on the complex variable method,the analytical solutions of stress functions and stress intensity factors are provided.The stress distribution along the axes and the edge of the elliptical hole is given graphically.The numerical results show that there is obvious stress concentration near the hole and cracks,and the stresses tend to applied loads at distances far from the defect,which conform to Saint-Venant's principle.Hence,the stress functions are proved to be right.Under special conditions,the present configuration becomes the Griffith crack,two symmetrical cracks emanating from an elliptical hole,two cracks of unequal length emanating from a circular hole,a crack at the edge of a circular hole,or a crack emanating from an elliptical hole.Compared with available results,stress intensity factors for these special shapes of ellipses and cracks show good coincidence.The stress intensity factor for two cracks of unequal length at the edge of an elliptical hole increases with the crack length and the major-to-minor axis ratio of the elliptical hole.The stress distribution in an infinite plate containing an elliptic hole with unsymmetrical cracks is given for the first time.

In the field of aerospace, high-speed trains and automobile, etc, analysis of temperature filed and scuffing failure of tapered roller bearings are more important than ever, and the scuffing failure of elements of such rolling bearings under heavy load and high speed still cannot be effectively predicted yet. A simplified model of tapered roller bearings consisted of one inner raceway, one outer raceway and a tapered roller was established, in which the interaction of several heat sources is ignored. The contact mechanics model, temperature model and model of scuffing failure are synthesized, and the corresponding computer programs are developed to analyze the effects of bearings parameters, different material and operational conditions on thermal performance of bearings, and temperature distribution and the possibility of surface scuffing are obtained. The results show that load, speed, thermal conductivity and tapered roller materials influence temperature rise and scuffing failure of bearings. Ceramic material of tapered roller results in the decrease of scuffing possibility of bearings to a high extent than the conventional rolling bearing steel. Compared with bulk temperature, flash temperature on the surfaces of bearing elements has a little influence on maximum temperature rise of bearing elements. For the rolling bearings operated under high speed and heavy load, this paper proposes a method which can accurately calculate the possibility of scuffing failure of rolling bearings.

Influence of geometric and cutting parameters of cemented carbide cutting tool on reliability of cutting tool has become more and more mature,yet influence of its physical and material parameters on reliability is still blank.In view of this,cutting test and fatigue crack growth test of YT05 cemented carbide cutting tool are conducted to measure such data as the original crack size,growth size,times of impact loading,number and time of cutting tool in failure,and stress distribution of cutting tool is also obtained by simulating cutting process of tools.Mathematical models on dynamic reliability and dynamic reliability sensitivity of cutting tool are derived respectively by taking machining time and times of impact loading into account,thus change rules of dynamic reliability sensitivity to physical and material parameters can be obtained.Theoretical and experimental results show that sensitive degree on each parameter of tools increases gradually with the increase of machining time and times of impact loading,especially for parameters such as fracture toughness,shape parameter,and cutting stress.This proposed model solves such problems as how to determine the most sensitive parameter and influence degree of physical parameters and material parameters to reliability,which is sensitivity,and can provide theoretical foundation for improving reliability of cutting tool system.

Current research on the operational reliability of centrifugal pumps has mainly focused on hydrodynamic instability. However, the interaction between the fluid and structure has not been sufficiently considered; this interaction can cause vibration and dynamic stress, which can affect the reliability. In this study, the dynamic stresses in a single-blade centrifugal pump impeller are analysed under different operating conditions; the two-way coupling method is used to calculate the fluid–structure interaction. Three-dimensional unsteady Reynolds-averaged Navier-Stokes equations are solved with the SST k–ω turbulence model for the fluid in the whole flow passage, while transient structure dynamic analysis is used with the finite element method for the structure side. The dynamic stresses in the rotor system are computed according to the fourth strength theory. The stress results show that the highest stress is near the loose bearing and that the equivalent stress increases with the flow rate because the dynamic stresses are closely related to the pressure load. The stress distributions on the blade pressure side, suction side, leading edge, and trailing edge are each analysed for different flow rates; the highest stress distribution is found on the pressure side. On the blade pressure side, a relatively large stress is found near the trailing edge and hub side. Based on these results, a stress distribution prediction method is proposed for centrifugal pumps, which considers the interaction between the fluid and structure. The method can be used to check the dynamic stress at different flow rates when optimising the pump design to increase the pump reliability.

The competition of surface and subsurface crack initiation induced failure is critical to understand very high cycle fatigue(VHCF)behavior,which necessitates the elucidation of the underlying mechanisms for the transition of crack initiation from surface to interior defects.Crack initiation potential in materials containing defects is investigated numerically by focusing on defect types,size,shape,location,and residual stress influences.Results show that the crack initiation potency is higher in case of serious property mismatching between matrix and defects,and higher strength materials are more sensitive to soft inclusions(elastic modulus lower than the matrix).The stress localization around inclusions are correlated to interior crack initiation mechanisms in the VHCF regime such as inclusion-matrix debonding at soft inclusions and inclusion-cracking for hard inclusions(elastic modulus higher than the matrix).It is easier to emanate cracks from the subsurface pores with the depth 0.7 times as large as their diameter.There exists an inclusion size independent region for crack incubation,outside which crack initiation will transfer from the subsurface soft inclusion to the interior larger one.As for elliptical inclusions,reducing the short-axis length can decrease the crack nucleation potential and promote the interior crack formation,whereas the long-axis length controls the site of peak stress concentration.The compressive residual stress at surface is helpful to shift crack initiation from surface to interior inclusions.Some relaxation of residual stress can not change the inherent crack initiation from interior inclusions in the VHCF regime.The work reveals the crack initiation potential and the transition among various defects under the influences of both intrinsic and extrinsic factors in the VHCF regime,and is helpful to understand the failure mechanism of materials containing defects under long-term cyclic loadings.

The current design of hydro-viscous clutch(HVC)in tracked vehicle fan transmission mainly focuses on high-speed and high power.However,the fluid torque under the influence of fluid temperature can not be predicted accurately by conventional mathematical model or experimental research.In order to validate the fluid torque of HVC by taking the viscosity-temperature characteristic of fluid into account,the test rig is designed.The outlet oil temperature is measured and fitted with different rotation speed,oil film thickness,oil flow rate,and inlet oil temperature.Meanwhile,the film torque can be obtained.Based on Navier-Stokes equations and the continuity equation,the mathematical model of fluid torque is proposed in cylindrical coordinate.Iterative method is employed to solve the equations.The radial and tangential speed distribution,radial pressure distribution and theoretical flow rate are determined and analyzed.The models of equivalent radius and fluid torque of friction pairs are introduced.The experimental and theoretical results indicate that tangential speed distribution is mainly determined by the relative rotating speed between the friction plate and the separator disc.However,the radial speed distribution and pressure distribution are dominated by pressure difference at the lower rotating speed.The oil film fills the clearance and the film torque increases with increasing rotating speed.However,when the speed reaches a certain value,the centrifugal force will play an important role on the fluid distribution.The pressure is negative at the outer radius when inlet flow rate is less than theoretical flow,so the film starts to shrink which decreases the film torque sharply.The theoretical fluid torque has good agreement with the experimental data.This research proposes a new fluid torque mathematical model which may predict the film torque under the influence of temperature more accurately.

首先对物流配送及相关理论进行了综述,提出了共同配送模式在广西-东盟物流中的应用,同时,对广西现行的自营配送模式与共同配送模式进行了比较,并从成本、路线、经营主体等方面进行了定性、定量分析,由此,得出了自营配送模式存在成本高、路线不完善、经济主体单一等一系列问题,而共同配送模式更适合于广西物流发展的现状,并提出了共同配送的三种组织模式在广西物流应用中的优势和劣势.最后,提出了共同配送模式在广西物流配送应用中需要注意的问题及其对策.

Now the optimization strategies for power distribution are researched widely,and most of them are aiming to the optimal fuel economy and the driving cycle must be preknown.Thus if the actual driving condition deviates from the scheduled driving cycle,the effect of optimal results will be declined greatly.Therefore,the instantaneous optimization strategy carried out on-line is studied in this paper.The power split path and the transmission efficiency are analyzed based on a special power-split scheme and the efficiency models of the power transmitting components are established.The synthetical efficiency optimization model is established for enhancing the transmission efficiency and the fuel economy.The identification of the synthetical efficiency as the optimization objective and the constrain group are discussed emphatically.The optimization is calculated by the adaptive simulated annealing(ASA)algorithm and realized on-line by the radial basis function(RBF)-based similar models.The optimization for power distribution of the hybrid vehicle in an actual driving condition is carried out and the road test results are presented.The test results indicate that the synthetical efficiency optimization method can enhance the transmission efficiency and the fuel economy of the power-split hybrid electric vehicle(HEV)observably.Compared to the rules-based strategy the optimization strategy is optimal and achieves the approximate global optimization solution for the power distribution.The synthetical efficiency optimization solved by ASA algorithm can give attentions to both optimization quality and calculation efficiency,thus it has good application foreground for the power distribution of power-split HEV.

Nondestructive techniques for appraising gas metal arc welding(GMAW) faults plays a very important role in on-line quality controllability and prediction of the GMAW process. On-line welding quality controllability and prediction have several disadvantages such as high cost, low efficiency, complication and greatly being affected by the environment. An enhanced, efficient evaluation technique for evaluating welding faults based on Mahalanobis distance(MD) and normal distribution is presented. In addition, a new piece of equipment, designated the weld quality tester(WQT), is developed based on the proposed evaluation technique. MD is superior to other multidimensional distances such as Euclidean distance because the covariance matrix used for calculating MD takes into account correlations in the data and scaling. The values of MD obtained from welding current and arc voltage are assumed to follow a normal distribution. The normal distribution has two parameters: the mean ? and standard deviation of the data. In the proposed evaluation technique used by the WQT, values of MD located in the range from zero to ?+3? are regarded as "good". Two experiments which involve changing the flow of shielding gas and smearing paint on the surface of the substrate are conducted in order to verify the sensitivity of the proposed evaluation technique and the feasibility of using WQT. The experimental results demonstrate the usefulness of the WQT for evaluating welding quality. The proposed technique can be applied to implement the on-line welding quality controllability and prediction, which is of great importance to design some novel equipment for weld quality detection.

以某拱坝为例,深入分析了不同固结灌浆阶段拱坝出现裂缝的成因和机理.高温季节控制固结灌浆上抬压力是避免开裂的关键;低温季节固结灌浆时表面温度应力是主导因素,尤其是出现长间歇期时.结合反馈分析与预报仿真结果,提出高温季节固结灌浆时应合理控制盖重厚度、灌浆压力以及灌浆开始的龄期;低温季节固结灌浆时,要做好保温工作.此外还可考虑采用无盖重灌浆来减小长间歇时间.