科创中国

Pneumatic actuators and electric actuators have almost been applied to all manufacturing industries.The two kinds of actuators can replace each other in most fields,such as the point to point transmission occasion and some rotating occasions.However,there are very few research results about the advantages and disadvantages of two kinds of actuators under the same working conditions so far.In this paper,a novel comprehensive assessment method,named as overall life cycle comprehensive assessment(OLCCA),is proposed for comparison and assessment of pneumatic and electric actuators.OLCCA contains mechanical properties evaluation(MPE),life cycle cost analysis based on users(LCCABOU)and life cycle environmental impact analysis(LCEIA)algorithm in order to solve three difficult problems:mechanical properties assessment,cost analysis and environmental impact assessment about actuators.The mechanical properties evaluation of actuators is a multi-objective optimization problem.The fuzzy data quantification and information entropy methods are combined to establish MPE algorithm of actuators.Two kinds of pneumatic actuators and electric actuators with similar bearing capacity and similar work stroke were taken for example to verify the correctness of MPE algorithm.The case study of MPE algorithm for actuators verified its correctness.LCCABOU for actuators is also set up.Considering cost complex structure of pneumatic actuators,public device cost even method(PDCEM)is firstly presented to solve cost division of public devices such as compressors,aftercooler,receivers,etc.LCCABOU method is also effective and verified by the three groups of pneumatic actuators and electric actuators.Finally,LCEIA model of actuators is established for the environmental impact assessment of actuators.LCEIA data collection method and model establishment procedure for actuators are also put forward.With Simapro 7,LCEIA comparison results of six actuators can be obtained:Fossil fuels are the major environmental factor of pneumatic and electric actuators;Environmental impact of electric actuator is large than one of pneumatic actuator under the similar mechanical properties and working conditions of pneumatic and electric actuators.The results are correct and correspond with the actual mechanical properties of actuators.This paper proposes a comprehensive evaluation method of the actuators,which can solve the critical problem that similar electromechanical products are very difficult to be compared with each other from the angle of performance,cost and environment impact.

分析传统学术论文和开放存取论文现有评价方法的不足与困难之处;融合层次分析法和同行评议所具有的优势,提出开放存取论文评价的框架、流程以及具体实现方法.最后通过实验验证其评价效果,结果显示该方法的评价结果与文章的真实值相近.

The mechanical properties and microstructure evolution of cold-deformed CrMnN austenitic stainless steel annealed in a temperature ranging from 50 ℃ to 650 ℃ for 90 min and at 550 ℃ for different time were investigated by tensile test, micro hardness test, and Transmission Electron Microscope (TEM). The steel was strengthened when it got annealed at temperatures ranging from 100 ℃ to 550 ℃, while it was softened when it got annealed at temperatures ranging from 550 ℃ to 650 ℃. Annealing temperature had stronger effect on mechanical properties than annealing time. TEM observations showed that nano-sized precipitates formed when the steel was annealed at 150 ℃ for 90 min, but the size and density of precipitates had no noticeable change with annealing temperature and time. Recrystallization occurred when the steel was annealed at temperatures above 550 ℃ for 90 min, and its scale increased with annealing temperature. Nano-sized annealing twins were observed. The mechanisms that controlled the mechanical behaviors of the steel were discussed.

在学校组织的正式教师工作评价体系之外,还存在着学生群体自发传播形成的对教师的非正式评价-教师口碑.教师口碑可以被纳入大学教师工作评价体系,成为评价大学教师教育教学的依据和参考.通过对北京地区六所研究型大学高年级本科生的问卷调查发现:高校中正式组织的学生评教活动在结果分析和信息公开等诸多方面仍普遍存在不足;在正式的信息获取渠道不完善的情况下,教师口碑是学生获得教师信息和分享课程经验的重要途径;大学教师口碑在学生中间主要通过口口相传的方式传播,具有较高的可信度和影响力;教师良好的修养学识和课堂教学能力是学生最关心的教师特质,而教师的科研能力、社会工作和荣誉等特质则因其所授课程的性质不同,而受到不同程度的关注.

Hydrostatic mechanical face seals for reactor coolant pumps are very important for the safety and reliability of pressurized-water reactor power plants.More accurate models on the operating mechanism of the seals are needed to help improve their performance.The thermal fluid–solid interaction(TFSI)mechanism of the hydrostatic seal is investigated in this study.Numerical models of the flow field and seal assembly are developed.Based on the mechanism for the continuity condition of the physical quantities at the fluid–solid interface,an on-line numerical TFSI model for the hydrostatic mechanical seal is proposed using an iterative coupling method.Dynamic mesh technology is adopted to adapt to the changing boundary shape.Experiments were performed on a test rig using a full-size test seal to obtain the leakage rate as a function of the differential pressure.The effectiveness and accuracy of the TFSI model were verified by comparing the simulation results and experimental data.Using the TFSI model,the behavior of the seal is presented,including mechanical and thermal deformation,and the temperature field.The influences of the rotating speed and differential pressure of the sealing device on the temperature field,which occur widely in the actual use of the seal,are studied.This research proposes an on-line and assembly-based TFSI model for hydrostatic mechanical face seals,and the model is validated by full-sized experiments.

Current researches show that mechanical deformation of seal ring face makes fluid film clearance decrease at high pressure side, thus a divergent clearance is formed and face wear occurs more seriously at the high pressure side than that on the low pressure side. However, there is still lack of published experimental works enough to prove the theoretical results. In this paper, a spiral groove dry gas seal at high pressures is experimentally investigated so as to prove the face wear happened at the high pressure side of seal faces due to the face mechanical deformation, and the wear behavior affected by seal ring structure is also studied. The experimental results show that face wear would occur at the high pressure side of seal faces due to the deformation, thus the leakage and face temperature increase, which all satisfies the theoretical predictions. When sealed pressure is not less than 5 MPa, the pressure can provide enough opening force to separate the seal faces. The seal ring sizes have obvious influence on face wear. Face wear, leakage and face temperature of a dry gas seal with the smaller cross sectional area of seal ring are less than that of a dry gas seal with bigger one, and the difference of leakage rate between these two sizes of seal face width is in the range of 24%–25%. Compared with the effect of seal ring sizes, the effect of secondary O-ring seal position on face deformation and face wear is less. The differences between these two types of dry gas seals with different secondary O-ring seal positions are less than 5.9% when the rotational speed varies from 0 to 600 r/min. By linking face wear and sealing performance changes to the shift in mechanical deformation of seal ring, this research presents an important experimental method to study face deformation of a dry gas seal at high pressures.

Innovation is a process of taking an original idea and converting it into a business value, in which the engineers face some inventive problems which can be solved hardly by experience. TRIZ, as a new theory for companies in China, provides both conceptual and procedural knowledge for finding and solving inventive problems. Because the government plays a leading role in the diffusion of TRIZ, too many companies from different industries are waiting to be trained, but the quantity of the trainers mastering TRIZ is incompatible with that requirement. In this context, to improve the training effect, an interactive training model of TRIZ for the mechanical engineers in China is developed and the implementation in the form of training classes is carried out. The training process is divided into 6 phases as follows: selecting engineers, training stage-1, finding problems, training stage-2, finding solutions and summing up. The government, TRIZ institutions and companies to join the programs interact during the process. The government initiates and monitors a project in form of a training class of TRIZ and selects companies to join the programs. Each selected companies choose a few engineers to join the class and supervises the training result. The TRIZ institutions design the training courses and carry out training curriculum. With the beginning of the class, an effective communication channel is established by means of interview, discussion face to face, E-mail, QQ and so on. After two years training practices, the results show that innovative abilities of the engineers to join and pass the final examinations increased distinctly, and most of companies joined the training class have taken congnizance of the power of TRIZ for product innovation. This research proposes an interactive training model of TRIZ for mechanical engineers in China to expedite the knowledge diffusion of TRIZ.

The existing research of steering comfort mainly focuses on the subjective evaluation,aiming at designing and optimizing the steering system.In the development of steering system,especially the evaluation of steering comfort,the objective evaluation methods considered the kinematic characteristics of driver steering maneuver are not proposed,which means that the objective evaluation of steering cannot be conducted with the evaluation of kinematic characteristics of driver in steering maneuver.In order to propose the objective evaluation methods of steering comfort,the evaluation of steering movement quality of driver is developed on the basis of the study of the kinematic characteristics of steering maneuver.First,the steering motion trajectories of the driver in both comfortable and certain extreme uncomfortable operation conditions are detected using the Vicon motion capture system.The operation conditions are under the restrictions of the vertical height and horizontal distance between steering wheel center and the H-point of driver,and the steering resisting torque else.Next,the movement quality evaluation of driver steering maneuver is assessed using twelve kinds of evaluation indices based on the kinematic analyses of the steering motion trajectories to propose an objective evaluation method.Finally,an integrated discomfort index of steering maneuver is proposed on the basis of the regression analysis of subjective evaluation rating and the movement quality evaluation indices,including the Jerk,Discomfort and Joint Torque indices.The test results show that the proposed integrated discomfort index gives a good fitting with the subjective evaluation of discomfort,which means it can be used to evaluate or predict the discomfort level of steering maneuver.This paper proposes an objective evaluation method of steering comfort based on the movement quality evaluation of driver steering maneuver.

针对期刊评价实践中专家评审数据获取困难的问题,建议利用现有引文数据库提供的信息构建新型专家评议指标,以测度期刊在学科专家群体中的影响力.提出期刊z指数指标并以国内图情类核心期刊为例进行实证研究,认为该方法能有效获取可反映专家评价意见的客观数据,而且具有成本低、可信度较高等优势.