科创中国

The current research of machine center accuracy in workspace mainly focuses on the poor geometric error subjected to thermal and gravity load while in operation,however,there are little researches focusing on the effect of machine center elastic deformations on workspace volume.Therefore,a method called pre-deformation for assembly performance is presented.This method is technically based on the characteristics of machine tool assembly and collaborative computer-aided engineering(CAE)analysis.The research goal is to enhance assembly performance,including straightness,positioning,and angular errors,to realize the precision of the machine tool design.A vertical machine center is taken as an example to illustrate the proposed method.The concept of travel error is defined to obtain the law of the guide surface.The machine center assembly performance is analyzed under cold condition and thermal balance condition to establish the function of pre-deformation.Then,the guide surface in normal direction is processed with the pre-deformation function,and the machine tool assembly performance is measured using a laser interferometer.The measuring results show that the straightness deviation of the Z component in the Y-direction is 158.9%of the allowable value primarily because of the gravity of the spindle head,and the straightness of the X and Y components is minimal.When the machine tool is processed in pre-deformation,the straightness of the Z axis moving component is reduced to 91.2%.This research proposes a pre-deformation machine center assembly method which has sufficient capacity to improving assembly accuracy of machine centers.

In the mixed-flow pump design,the shape of the flow passage can directly affect the flow capacity and the internal flow,thus influencing hydraulic performance,cavitation performance and operation stability of the mixed-flow pump.However,there is currently a lack of experimental research on the influence mechanism.Therefore,in order to analyze the effects of subtle variations of the flow passage on the mixed-flow pump performance,the frustum cone surface of the end part of inlet contraction flow passage of the mixed-flow pump is processed into a cylindrical surface and a test rig is built to carry out the hydraulic performance experiment.In this experiment,parameters,such as the head,the efficiency,and the shaft power,are measured,and the pressure fluctuation and the noise signal are also collected.The research results suggest that after processing the inlet flow passage,the head of the mixed-flow pump significantly goes down;the best efficiency of the mixed-flow pump drops by approximately 1.5%,the efficiency decreases more significantly under the large flow rate;the shaft power slightly increases under the large flow rate,slightly decreases under the small flow rate.In addition,the pressure fluctuation amplitudes on both the impeller inlet and the diffuser outlet increase significantly with more drastic pressure fluctuations and significantly lower stability of the internal flow of the mixed-flow pump.At the same time,the noise dramatically increases.Overall speaking,the subtle variation of the inlet flow passage leads to a significant change of the mixed-flow pump performance,thus suggesting a special attention to the optimization of flow passage.This paper investigates the influence of the flow passage variation on the mixed-flow pump performance by experiment,which will benefit the optimal design of the flow passage of the mixed-flow pump.

For planning optimum multiple stresses accelerated life test plans, a commonly followed guiding principle is that all parameters of the life-stress relationship should be estimated, and the number of the stress level combinations must be no less than the number of parameters of the life-stress relationship. However, the general objective of an accelerated life test(ALT) is to assess the p-th quantile of the product life distribution under normal stress. For this objective, estimating all model parameters is not necessary, and this will increase the cost of test. Based on the theoretical conclusion that the stress level combinations of the optimum multiple stresses ALT plan locate on a straight line through the origin of coordinate, it is proposed that a design idea of planning the optimum multiple stresses ALT plan through transforming the problem of designing an optimum multiple stresses ALT plan to designing an optimum single stress ALT plan. Moreover, a method of planning the optimum multiple stresses ALT plan which can avoid estimating all model parameters is established. An example shows that, the proposed plan which only has two stress level combinations could achieve an accuracy no less than the traditional plan, and save the test time and cost on one stress level combination at least; when the actual product life is less than the design value, even the deviation of the model initial parameters value is up to 20%, the variance of the estimation of the p-th quantile of the proposed plan is still smaller than the traditional plans approximately 25%. A design method is provided for planning the optimum multiple stresses ALT which uses the statistical optimum degenerate test plan as the optimum multiple stresses accelerated life test plan.

声学多普勒水流剖面仪是目前较先进的河道测流设备.按《规范》要求,利用该仪器前,需要对该仪器与流速仪测流的实测流量进行对比实验,计算其换算系数.在分析ADCP测流原理的基础上,利用引黄干渠张二庄水文站实测流量资料,对两种测流方法测量结果进行对比分析.根据最小二乘法原理,建立回归直线,并对其进行检验.对回归直线进行拟合优度检验,拟合优度系数为0.982;对回归直线用F检验法进行截距检验,回归效果显著.在该断面用ADCP测流时,流量换算系数为0.9911.

Drill sampling has been widely employed as an effective way to acquire deep samples in extraterrestrial exploration. A novel sampling method, namely, flexible-tube coring, was adopted for the Chang'e mission to acquire drilling cores without damaging stratification information. Since the extraterrestrial environment is uncertain and different from the terrestrial environment, automated drill sampling missions are at risk of failure. The principles of drilling and coring for the lunar subsurface should be fully tested and verified on earth before launch. This paper proposes a test-bed for conducting the aforementioned experiments on earth. The test-bed comprises a rotary-percussive drilling mechanism, penetrating mechanism, drilling medium container, and signal acquisition and control system. For granular soil, coring experiments indicate that the sampling method has a high coring rate greater than 80%. For hard rock, drilling experiments indicate that the percussive frequency greatly affects the drilling efficiency. A multi-layered simulant composed of granular soil and hard rock is built to test the adaptability of drilling and coring. To tackle complex drilling media, an intelligent drilling strategy based on online recognition is proposed to improve the adaptability of the sampling drill. The primary features of this research are the proposal of a scheme for drilling and coring a test-bed for validation on earth and the execution of drilling experiments in complex media.

The methods of improving the dynamic performance of high speed on/off solenoid valve include increasing the magnetic force of armature and the slew rate of coil current, decreasing the mass and stroke of moving parts. The increase of magnetic force usually leads to the decrease of current slew rate, which could increase the delay time of the dynamic response of solenoid valve. Using a high voltage to drive coil can solve this contradiction, but a high driving voltage can also lead to more cost and a decrease of safety and reliability. In this paper, a new scheme of parallel coils is investigated, in which the single coil of solenoid is replaced by parallel coils with same ampere turns. Based on the mathematic model of high speed solenoid valve, the theoretical formula for the delay time of solenoid valve is deduced. Both the theoretical analysis and the dynamic simulation show that the effect of dividing a single coil into N parallel sub-coils is close to that of driving the single coil with N times of the original driving voltage as far as the delay time of solenoid valve is concerned. A specific test bench is designed to measure the dynamic performance of high speed on/off solenoid valve. The experimental results also prove that both the delay time and switching time of the solenoid valves can be decreased greatly by adopting the parallel coil scheme. This research presents a simple and practical method to improve the dynamic performance of high speed on/off solenoid valve.

在以往的服务管理研究中,服务绩效的影响因素很多,然而没有文献研究员工对服务的概念性界定对服务绩效的影响.基于行为识别理论,文章提出服务认知一行为模式对一线员工的服务绩效存在影响.该研究利用旅行社业和饭店业402名一线服务员工的问卷调查数据,部分验证了所提出的假设,实证结果发现:(1)对顾客理解型服务认知一行为模式具有最高的角色外服务绩效,对工作规范型服务认知一行为模式具有最低的角色外服务绩效;(2)对工作规范型服务认知一行为模式具有最低的角色内服务绩效,对顾客理解型和手段型服务认知一行为模式具有较高的角色内服务绩效.

水平衡测试是加强用水科学管理,最大限度地节约用水与合理用水的一项基础工作.解释了水平衡测试的定义及开展测试工作的依据,分析了水平衡测试参数之间关系,介绍了水平衡测试的方法,结合承德市中心医院水平衡测试实例,分析其用水现状,为制定用水定额和计划用水量指标,提供了较准确的基础数据,为今后节约用水提出了合理化的建议.

The transient behavior of centrifugal pumps during transient operating periods,such as startup and stopping,has drawn more and more attention recently because of urgent needs in engineering.Up to now,almost all the existing studies on this behavior are limited to using water as working fluid.The study on the transient behavior related to solid-liquid two-phase flow has not been seen yet.In order to explore the transient characteristics of a high specific-speed centrifugal pump during startup period delivering the pure water and solid-liquid two-phase flow,the transient flows inside the pump are numerically simulated using the dynamic mesh method.The variable rotational speed and flow rate with time obtained from experiment are best fitted as the function of time,and are written into computational fluid dynamics(CFD)code-FLUENT by using a user defined function.The predicted heads are compared with experimental results when pumping pure water.The results show that the difference in the transient performance during startup period is very obvious between water and solid-liquid two-phase flow during the later stage of startup process.Moreover,the time for the solid-liquid two-phase flow to achieve a stable condition is longer than that for water.The solid-liquid two-phase flow results in a higher impeller shaft power,a larger dynamic reaction force,a more violent fluctuation in pressure and a reduced stable pressure rise comparing with water.The research may be useful to understanding on the transient behavior of a centrifugal pump under a solid-liquid two-phase flow during startup period.

物流企业员工绩效考核的内容主要包括员工的态度和能力考核,物流企业员工绩效指标设计的内容分为绩效维度、能力维度、态度维度和个人素质等方面.物流企业员工指标体系设计的考核采用360绩效考核,考核方法主要采用KPI法和AHP法,把绩效考核的结果在报酬运用、工作调整、开发潜能等方面进行运用.