科创中国

试验旨在研究玉米DDGS替代豆粕对草鱼(ctenopharvngodon idellus)幼鱼生长性能、血清生化指标和免疫指标的影响,选用360尾初重为(5.52±0.09)g的草鱼苗,随机分为6个处理组,分别设为D0、Dl、D2、D3、D4、D5组,每个处理组设3个重复,每个重复20尾,分别投喂用0、10%、20%、30%、40%、50%玉米DDGS替代豆粕的6种等氮饲料,饲养3周:结果表明:玉米DDGS添加量在30%以下时对草鱼生长性能没有显著影响(P>0.05);添加量在40%~50%时草鱼生长性能显著下降(P<0.05),与对照组比较各试验组血清生化指标无显著差异(P>0.05);免疫指标试验组一氧化氮、超氧化物歧化酶与对照组相比无显著差异(P>0.05);总抗氧化能力50%组显著高于0、10%和30%组(P<0.05);20%组丙二醛含量显著低于对照组(P<0.05);试验组碱性磷酸酶活性与对照组相比有显著差异(P

黄文庆,王国霞,罗志锋,林佳男,李国立,黄燕华 - 饲料工业

文章来源： 万方数据

目的表皮干细胞是组织工程化皮肤的"种子细胞".文中研究碱性成纤维细胞生长因子(basic fibroblast growth factor,bFGF)、胰岛素样细胞生长因子-1(insulin-like growth factor-1,IGF-1)和转化生长因子仅(transforming growth factor a,TGFa)对人表皮干细胞增殖的影响.方法采用两步酶消化法和Ⅳ型胶原差速贴壁相结合的方法获得人原代表皮干细胞,将表皮干细胞分为A组(K-SFM)、B组(K-SFM+bFGF)、C组(K-SFM+IGF-1)及D组(K-SFM+TGFot)进行培养.比较不同组之间表皮干细胞的克隆形成率、生长增殖、生长曲线和细胞周期等指标.结果B组、C组及D组培养的表皮干细胞在细胞增殖、细胞克隆率方面检测结果均明显高于A组(P〈0.05);流式细胞仪检测B组、C组与A组及D组处于G0/G1细胞比例比较差异有统计学意义(P〈0.05).结论IGF-1、bFGF及TGF-a均对表皮干细胞的增殖有促进作用,IGF-1及bFGF对表皮干细胞表型的维持有较好的作用.

The methods of improving the dynamic performance of high speed on/off solenoid valve include increasing the magnetic force of armature and the slew rate of coil current, decreasing the mass and stroke of moving parts. The increase of magnetic force usually leads to the decrease of current slew rate, which could increase the delay time of the dynamic response of solenoid valve. Using a high voltage to drive coil can solve this contradiction, but a high driving voltage can also lead to more cost and a decrease of safety and reliability. In this paper, a new scheme of parallel coils is investigated, in which the single coil of solenoid is replaced by parallel coils with same ampere turns. Based on the mathematic model of high speed solenoid valve, the theoretical formula for the delay time of solenoid valve is deduced. Both the theoretical analysis and the dynamic simulation show that the effect of dividing a single coil into N parallel sub-coils is close to that of driving the single coil with N times of the original driving voltage as far as the delay time of solenoid valve is concerned. A specific test bench is designed to measure the dynamic performance of high speed on/off solenoid valve. The experimental results also prove that both the delay time and switching time of the solenoid valves can be decreased greatly by adopting the parallel coil scheme. This research presents a simple and practical method to improve the dynamic performance of high speed on/off solenoid valve.

在以往的服务管理研究中,服务绩效的影响因素很多,然而没有文献研究员工对服务的概念性界定对服务绩效的影响.基于行为识别理论,文章提出服务认知一行为模式对一线员工的服务绩效存在影响.该研究利用旅行社业和饭店业402名一线服务员工的问卷调查数据,部分验证了所提出的假设,实证结果发现:(1)对顾客理解型服务认知一行为模式具有最高的角色外服务绩效,对工作规范型服务认知一行为模式具有最低的角色外服务绩效;(2)对工作规范型服务认知一行为模式具有最低的角色内服务绩效,对顾客理解型和手段型服务认知一行为模式具有较高的角色内服务绩效.

The transient behavior of centrifugal pumps during transient operating periods,such as startup and stopping,has drawn more and more attention recently because of urgent needs in engineering.Up to now,almost all the existing studies on this behavior are limited to using water as working fluid.The study on the transient behavior related to solid-liquid two-phase flow has not been seen yet.In order to explore the transient characteristics of a high specific-speed centrifugal pump during startup period delivering the pure water and solid-liquid two-phase flow,the transient flows inside the pump are numerically simulated using the dynamic mesh method.The variable rotational speed and flow rate with time obtained from experiment are best fitted as the function of time,and are written into computational fluid dynamics(CFD)code-FLUENT by using a user defined function.The predicted heads are compared with experimental results when pumping pure water.The results show that the difference in the transient performance during startup period is very obvious between water and solid-liquid two-phase flow during the later stage of startup process.Moreover,the time for the solid-liquid two-phase flow to achieve a stable condition is longer than that for water.The solid-liquid two-phase flow results in a higher impeller shaft power,a larger dynamic reaction force,a more violent fluctuation in pressure and a reduced stable pressure rise comparing with water.The research may be useful to understanding on the transient behavior of a centrifugal pump under a solid-liquid two-phase flow during startup period.

物流企业员工绩效考核的内容主要包括员工的态度和能力考核,物流企业员工绩效指标设计的内容分为绩效维度、能力维度、态度维度和个人素质等方面.物流企业员工指标体系设计的考核采用360绩效考核,考核方法主要采用KPI法和AHP法,把绩效考核的结果在报酬运用、工作调整、开发潜能等方面进行运用.

The existing research on improving the hydraulic performance of centrifugal pumps mainly focuses on the design method and the parameter optimization.The traditional design method for centrifugal impellers relies more on experience of engineers that typically only satisfies the continuity equation of the fluid.In this study,on the basis of the direct and inverse iteration design method which simultaneously solves the continuity and motion equations of the fluid and shapes the blade geometry by controlling the wrap angle,three centrifugal pump impellers are designed by altering blade wrap angles while keeping other parameters constant.The three-dimensional flow fields in three centrifugal pumps are numerically simulated,and the simulation results illustrate that the blade with larger wrap angle has more powerful control ability on the flow pattern in impeller.The three pumps have nearly the same pressure distributions at the small flow rate,but the pressure gradient increase in the pump with the largest wrap angle is smoother than the other two pumps at the design and large flow rates.The pump head and efficiency are also influenced by the blade wrap angle.The highest head and efficiency are also observed for the largest angle.An experiment rig is designed and built to test the performance of the pump with the largest wrap angle.The test results show that the wide space of its efficiency area and the stability of its operation ensure the excellent performance of the design method and verify the numerical analysis.The analysis on influence of the blade wrap angle for centrifugal pump performance in this paper can be beneficial to the optimization design of the centrifugal pump.

本文以全要素生产率对经济增长的贡献率作为经济增长方式衡量指标,对2000-2010年间中国工业经济增长方式的变化特征进行了分析,在此基础上利用30个工业行业面板数据,从总体和行业分组两个层面分别考察出口、进口和FDI对中国工业经济增长方式的影响.研究表明:中国工业经济增长方式的粗放型特征不仅不存在弱化趋向,反而出现强化现象;出口对工业经济增长方式转变不具有明显促进作用,在不同要素密集度特征和不同平均规模特征的工业行业中均如此;进口对工业经济增长方式转型存在推进作用,在资源和劳动密集型、平均规模较大的工业行业中尤为明显;FDI增加会带动中国工业经济增长方式转型,资本和技术密集型、平均规模较大的工业行业FDI对本行业经济增长方式转型的拉动作用大于资源和劳动密集型、平均规模较小的工业行业.

CdSe/CdS semiconductor quantum dots co-sensitized TiO2 nanorod array was fabricated on the transparent conductive fluorine-doped tin oxide (FTO) substrate using the hydrothermal and successive ionic layer adsorption and reaction (SILAR) process. The structural and morphological properties of the samples were characterized by X-ray diffraction (XRD), field-emission scanning electron microscopy (FESEM), and transmission electron microscopy (TEM). The results indicate that CdSe/CdS QDs are uniformly coated on the surface of the TiO2 nanorods. The shift of light absorption edge was monitored by taking UV-visible absorption spectra. Compared with the absorption spectra of the TiO2 nanorod array, deposition of CdSe/CdS QDs shifts the absorption edge to the higher wavelength. The enhanced light absorption in the visible-light region of CdSe/CdS/TiO2 nanorod array indicates that CdSe/CdS layers can act as co-sensitizers in quantum dots sensitized solar cells (QDSSCs). By optimizing the CdSe layer deposition cycles, a photocurrent of 5.78 mA/cm2, an open circuit photovoltage of 0.469 V and a conversion efficiency of 1.34 % were obtained under an illumination of 100 mw/cm2.

Traditional model for calculating performance parameters of a fix-pad journal bearing leads to heavy workload,complicated and changeable formulae as it requires deriving various geometric formulae with different bearing types such as circular journal bearing,dislocated bearing and elliptic bearing.Considering different pad preload ratios for non-standard bearing,traditional model not only becomes more complicated but also reduces scalability and promotion of the calculation programs.For the complexly case of traditional model while dealing with various fix-pad journal bearings,unified coordinate system model for performance calculation of fix-pad journal bearing is presented in the paper.A unified coordinate system with the bearing center at the origin is established,and the eccentricity ratio and attitude angle of axis relative to each pad are calculated through the coordinates of journal center and each pad center.Geometric description of fix-pad journal bearing is unified in this model,which can be used for both various standard bearing and non-standard bearing with different pad preload ratios.Validity of this model is verified with an elliptical bearing.Performance of a non-standard four-leaf bearing with different pad preload ratios is calculated based on this model.The calculation result shows that increasing preload ratio of the pad 1 and keeping that of the left three pads constant improves bearing capacity,stiffness and damping coefficients.This research presents a unified coordinate system model unifies performance calculation of fix-pad journal bearings and studied a non-standard four-leaf bearing with different pad preload ratios,the research conclusions provides new methods for performance calculation of fix-pad journal bearings.